Buggies Unlimited Golf Cart Troubleshooting Text Support

92-94 EZ-GO Gas Carb adjustment

92-94 EZ-GO Gas Carb adjustment

Postby EZ-GO WA » Thu May 11, 2006 12:56 am

I'm new to this forum. Does anyone have a diagram and instructions on how to fully adjust or how the settings should be on a 92-94 EZ-GO Gas carburetor????? Thanks for the help.
Have a "Blessed Day!"
EZ-GO WA
 
Posts: 6
Joined: Thu May 11, 2006 12:26 am

Postby Bob-0 » Thu May 11, 2006 7:04 pm

Are you looking to adjust the linkage or the idle speed screw?

Bob
Commercial Pilot ASEL & AMEL; CFI-IA, AMEI
There is no level of skill so high that it cannot be overcome by sufficiently poor judgment
Image
User avatar
Bob-0
 
Posts: 5169
Joined: Fri Jan 20, 2006 6:38 pm
Location: Arkansas

RE: Carb???

Postby EZ-GO WA » Thu May 11, 2006 7:28 pm

All the adjustment screws. I know they are out of wack and want to know how they should be set to make the engine run / not flood out. A diagram would be awesome also so I know exactly which screws I am adjusting.
Have a "Blessed Day!"
EZ-GO WA
 
Posts: 6
Joined: Thu May 11, 2006 12:26 am

RE: Carb update!

Postby EZ-GO WA » Thu May 11, 2006 7:45 pm

OK, my mistake. I finally know now that it is a 1995 EZ-GO with the 295cc engine.
Have a "Blessed Day!"
EZ-GO WA
 
Posts: 6
Joined: Thu May 11, 2006 12:26 am

Postby ezgomike » Thu May 11, 2006 9:05 pm

There are only two adjustments to this carb.

The pilot screw is on the top of the carb, closest to the cylinder head. Lightly seat the screw, and turn it out 1 - 1/2 turns.

The idle stop screw is on the driver's side of the carb, and goes through the carb body then touches the throttle lever. Back it all the way out(up), then make sure there is a little slack in the long linkage rod on the side of the engine. Then turn the idle stop screw down just until it touches the throttle lever.
User avatar
ezgomike
 
Posts: 4304
Joined: Tue Aug 02, 2005 11:43 pm
Location: 1-800-678-1123

RE: carb

Postby EZ-GO WA » Thu May 11, 2006 11:58 pm

Thanks for the info. I'll let you all know if I get it running. Have a mechanic neighbor who thinks the float in the carb is stuck. Hopefully that's my problem as to why it isn't starting.
Have a "Blessed Day!"
EZ-GO WA
 
Posts: 6
Joined: Thu May 11, 2006 12:26 am

Re: RE: carb

Postby ezgomike » Fri May 12, 2006 9:30 pm

EZ-GO WA wrote:Thanks for the info. I'll let you all know if I get it running. Have a mechanic neighbor who thinks the float in the carb is stuck. Hopefully that's my problem as to why it isn't starting.


Gas in the airbox?

Spitting out fuel, and hard to start?

Set the intake valves for .004" clearance between the cam, and rocker(at low spot on cam).
User avatar
ezgomike
 
Posts: 4304
Joined: Tue Aug 02, 2005 11:43 pm
Location: 1-800-678-1123


Return to EZGO Gas

Who is online

Users browsing this forum: No registered users and 9 guests